The 50-V5 integrates preform injection, stretch blowing and take-out in a three-station machine. Its selection table covers one to six cavities, with a different bottle envelope for each arrangement.
Evaluate the actual cavity row against your container drawing before choosing the mold configuration.
The one-cavity reference lists a maximum body diameter of 90 mm and a 60 mm neck. At six cavities, the corresponding reference is a 28 mm body diameter and a 17 mm neck. The listed maximum bottle height is 200 mm.
These are configuration-dependent limits. Each cavity arrangement needs its own bottle and mold assessment.
Form the preform for the selected bottle and mold arrangement.
Stretch and blow the preform into the container.
Remove the container through the configured take-out sequence.
Review the injection unit, station movements and machine envelope together when defining the proposed mold and production configuration.
| Parameter | Specification |
|---|---|
| Stations | 3 |
| Installed power | 20 kW |
| Dimensions, L × W × H | 3.4 × 1.2 × 2.5 m |
| Machine weight | 3.5 t |
| Parameter | Specification |
|---|---|
| Screw diameter | 35 mm |
| Theoretical injection volume | 130 cm³ |
| Injection rate | 90 cm³/s |
| Injection pressure | 160 MPa |
| Screw rotation speed | 0–200 rpm |
| Parameter | Specification |
|---|---|
| Injection clamping force | 100 kN |
| Injection upper stroke | 450 mm |
| Injection lower stroke | 225 mm |
| Blow clamping force | 70 kN |
| Blow core stroke | 200 mm |
| Blow mold opening stroke | 70 mm |
| Take-out stroke | 100 mm |
Installed power is used for electrical planning. Operating consumption must be measured for the agreed bottle, mold and auxiliary equipment.
Evaluate the proposed mold with the injection specification. The 35 mm screw, 130 cm³ theoretical injection volume, 90 cm³/s injection rate and 160 MPa injection pressure describe the injection unit. The tool proposal should connect bottle weight to the total shot requirement and identify the cycle used to calculate finished-bottle output.
Read each row as one configuration reference. Body diameter, neck size, height and weight from different rows must not be combined.
Swipe horizontally to view all columns.
| Cavities | Body diametermm | Bottle heightmm | Neck sizemm | Bottle weightg |
|---|---|---|---|---|
| 1 | 90 | 200 | 60 | 105 |
| 2 | 80 | 200 | 38 | 50 |
| 3 | 64 | 200 | 30 | 35 |
| 4 | 45 | 200 | 27 | 28 |
| 5 | 35 | 200 | 20 | 22 |
| 6 | 28 | 200 | 17 | 18 |
Catalog configuration references. Final suitability depends on the complete bottle, preform and mold design. The six-cavity reference applies to a smaller container than the one-cavity reference.
Use the machine dimensions and movement data to review the complete working cell, including tool access and container removal.
The 50-V5 combines a 3.4 m machine length with a 1.2 m width and a 2.5 m height. These dimensions help your production team begin its layout study alongside material preparation, cooling equipment and container handling.
The machine envelope is only part of the working cell. Allow access to the mold, injection unit and service connections, including the path used to remove a mold.
The injection station lists 450 mm of upper stroke and 225 mm of lower stroke. The blow station lists a 200 mm core stroke and a 70 mm mold opening stroke, followed by a 100 mm take-out stroke.
These dimensions describe different machine movements. Check preform tooling, neck handling and the removal sequence against the machine interface drawing, even when the finished bottle fits a listed size row.
A similar bottle-size table does not establish identical injection capability or operating costs. The two models have different injection-unit specifications and strokes, so the tooling needs a separate review.
| Injection specification | 50-V5 | 50-S6 |
|---|---|---|
| Screw diameter | 35 mm | 36 mm |
| Theoretical injection volume | 130 cm³ | 146 cm³ |
Clarify the cavity references, electrical rating and comparison points before requesting a machine configuration.
No. The six-cavity row lists a 28 mm body and a 17 mm neck, while the one-cavity row lists 90 mm and 60 mm. Each row describes a different configuration.
It is the catalog installed-power figure. Operating consumption needs a measurement for the agreed bottle, mold and auxiliaries; it cannot be calculated from that figure alone.
The catalog injection units differ: 50-V5 lists a 35 mm screw and 130 cm³ theoretical injection volume, whereas 50-S6 lists 36 mm and 146 cm³. Their injection strokes also differ, so tooling needs separate review.
Send your bottle requirements for a quotation covering the injection unit, mold cavitation, utility requirements and included auxiliary equipment.
Include a drawing link in your message, or email your drawing to info@isbmmachine.net.
Cycle time and accepted output should be established using the proposed bottle and mold.