The 700-V4 has separate injection, conditioning, blowing and take-out stations. Its bottle reference table lists a 350 mm height across the available cavity entries, with neck and body limits that change by mold layout.
Review the neck geometry, bottle dimensions and matched screw option together before selecting the tooling configuration.
The 350 mm height reference is listed across all eleven cavity layouts. Neck, body and bottle-weight references must be taken from the selected row.
The one-cavity reference pairs a 204 mm body with a 149 mm neck. At four cavities, the reference is a 120 mm body and a 95 mm neck. Both list a 350 mm height, but each represents a different mold layout.
At twelve cavities, the body and neck references reduce to 37 mm and 18 mm. The full table supports an initial assessment of tall-container projects without implying that all widths, necks and cavity counts can be combined.
Form the preform using the selected 45, 50 or 60 mm screw configuration.
Condition the preform at a separate station before stretch blowing.
Stretch and blow the preform into the specified bottle body.
Remove the molded container through the configured take-out arrangement.
Check the machine envelope, clamping forces and individual station movements against the bottle, preform and mold drawings.
| Parameter | Specification |
|---|---|
| Drive | Hydraulic |
| Stations | 4 |
| Process sequence | Injection, conditioning, stretch blowing, take-out |
| Heating power | 13 kW |
| Oil tank capacity | 380 L |
| Dimensions, L × W × H | 5.4 × 2.15 × 3.3 m |
| Machine weight | 13 t |
Confirm the final electrical supply, connected loads and auxiliary requirements in the installation proposal.
| Parameter | Specification |
|---|---|
| Injection clamping force | 700 kN |
| Injection upper stroke | 450 mm |
| Injection lower stroke | 325 mm |
| Conditioning core stroke | 275 mm |
| Conditioning cavity stroke | 250 mm |
| Blow clamping force | 265 kN |
| Blow core stroke | 275 mm |
| Blow mold opening stroke | 300 mm |
| Take-out stroke | 150 mm |
Assess all four stations for the selected container. Injection, conditioning, blowing and take-out movements serve different parts of the tooling sequence. Check each movement alongside the bottle and preform drawings, including neck handling and removal.
Selecting a larger screw changes injection volume, rate and pressure together. Keep the values in each column attached to the same proposed configuration.
Swipe horizontally to compare all screw options.
| Parameter | 45 mm screw | 50 mm screw | 60 mm screw |
|---|---|---|---|
| Theoretical injection volumecm³ | 389 | 481 | 692 |
| Injection ratecm³/s | 190 | 240 | 340 |
| Injection pressureMPa | 217 | 176 | 122 |
| Screw rotation speedrpm | 0 ~ 150 | ||
The 692 cm³ volume belongs to the 60 mm screw and cannot be paired with the 217 MPa pressure entry from the 45 mm column. Specify one complete injection option in the quotation.
Body diameter, neck size and bottle-weight references change with cavity count. Read each row as one matched layout and verify it against the proposed bottle.
Swipe horizontally to view all columns.
| Cavities | Body diametermm | Bottle heightmm | Neck sizemm | Weight referenceg |
|---|---|---|---|---|
| 1 | 204 | 350 | 149 | 311 |
| 2 | 153 | 350 | 120 | 156 |
| 3 | 130 | 350 | 99 | 104 |
| 4 | 120 | 350 | 95 | 78 |
| 5 | 99 | 350 | 73 | 62 |
| 6 | 79 | 350 | 57 | 52 |
| 7 | 66 | 350 | 42 | 44 |
| 8 | 54 | 350 | 36 | 39 |
| 9 | 53 | 350 | 34 | 35 |
| 10 | 45 | 350 | 27 | 31 |
| 12 | 37 | 350 | 18 | 26 |
Dimensions and weight references from different rows must not be combined. The 149 mm neck reference applies to one cavity; the twelve-cavity row has an 18 mm neck reference.
Final suitability depends on the bottle, preform and mold design. Include the resin grade and target bottle mass in the project review.
Provide the bottle drawing, resin grade, target mass, output requirement and existing mold interfaces so the proposed configuration can be reviewed as a complete system.
The injection upper and lower strokes are 450 and 325 mm. Conditioning uses a 275 mm core stroke and a 250 mm cavity stroke; the blow station lists a 275 mm core stroke and a 300 mm opening stroke.
Check these movements with the preform length, neck-handling arrangement and mold drawings. Include the 150 mm take-out stroke when reviewing how the finished container will be removed.
The listed machine envelope is 5.4 × 2.15 × 3.3 m, with a weight of 13 t. Confirm auxiliary equipment and service clearance on the installation drawing.
Keep the selected screw configuration, mold interfaces and final utility schedule attached to the same proposal. Establish the installation layout around the equipment to be supplied.
The 250-V4S is relevant for some larger-neck projects, but its hybrid drive, injection specification and height references differ. Compare both models using the same container, preform and mold requirements.
For the 700-V4, identify which of the three screw options is being proposed. The comparison below uses its 60 mm option only for the injection-volume row.
| Reference | 700-V4 | 250-V4S |
|---|---|---|
| Drive | Hydraulic | Hybrid |
| One-cavity neck size | 149 mm | 146 mm |
| One-cavity height | 350 mm | 310 mm |
| Injection volume with 60 mm screw | 692 cm³ | 508 cm³ |
Review screw-option relationships, the information required for bottle selection and the basis for comparing related models.
No. The 60 mm option has the largest listed volume and rate, while the 45 mm option has the highest listed injection pressure. Keep the original column relationships.
No. Neck geometry, body dimensions, height, weight and cavity layout are all needed. Verify the proposed bottle and mold against one complete cavity layout.
The 250-V4S is relevant for some larger-neck projects, but its hybrid drive, shot specification and height references differ. Compare both using one bottle drawing.
Provide the bottle drawing, resin grade, target mass, output requirement and existing mold interfaces. Request a matched screw option and tooling proposal for the selected cavity layout.
Share a drawing link in the message, or send your files to info@isbmmachine.net.
The proposal should identify the injection option, station requirements and installation arrangement for your container.